logo
biểu ngữ biểu ngữ

Thông tin chi tiết

Nhà > Tin tức >

Tin tức công ty về Expansion Tank vs. Buffer Tank vs. Thermal Storage Tank – Part 4: Tank Selection, Sizing, Design and Installation in Heat Pump Systems

Sự kiện
Liên hệ với chúng tôi
Mr. Luke
86-757-22860323
wechat +8618666366485
Liên hệ ngay bây giờ

Expansion Tank vs. Buffer Tank vs. Thermal Storage Tank – Part 4: Tank Selection, Sizing, Design and Installation in Heat Pump Systems

2026-11-18

Expansion Tank vs. Buffer Tank vs. Thermal Storage Tank – Part 4: Tank Selection, Sizing, Design and Installation in Heat Pump Systems

Introduction

In an air-to-water heat pump system, selecting a high-efficiency heat pump is only the first step toward achieving reliable performance, indoor comfort and low operating costs.

The design of the water system is equally important, particularly the selection, sizing and installation of buffer tanks and thermal energy storage tanks.

An undersized water tank may result in frequent compressor cycling, insufficient thermal storage and unstable water temperatures. An oversized tank, however, may increase initial investment, standby heat losses and system response time.

Furthermore, inappropriate material selection, insufficient insulation, incorrect pipe connection positions and poor structural design can significantly affect overall system performance.

In the previous three articles of this technical series, we discussed:

  • Part 1: Expansion Tanks – Pressure Control and System Protection

  • Part 2: Buffer Tanks – Hydraulic Stability and Compressor Protection

  • Part 3: Thermal Storage Tanks – Energy Storage and Operating Cost Optimization

In this fourth article, we will explain how to correctly select, size, design and install water tanks for air-source heat pump heating and cooling systems.

1. Why Is Correct Water Tank Sizing Important?

One of the most frequently asked questions in the HVAC industry is:

How large should a buffer tank or thermal storage tank be for a heat pump system?

There is no universal answer because different applications have different hydraulic and thermal requirements.

If the water tank is too small

An undersized tank may cause:

  • Frequent compressor start-stop cycles, also known as short cycling.

  • Rapid fluctuations in supply and return water temperatures.

  • Insufficient thermal energy available during defrosting.

  • Reduced system stability under partial-load conditions.

  • Insufficient thermal storage capacity.

  • Increased mechanical stress on system components.

If the water tank is too large

An oversized tank may result in:

  • Higher equipment and installation costs.

  • Longer initial heating or cooling times.

  • Increased standby thermal losses.

  • Greater installation space requirements.

  • Additional structural loading.

  • Difficulty completing thermal charging within the available operating period.

For example, if an office building uses a large thermal storage tank with an undersized heat pump, the heat pump may not have sufficient capacity to charge the tank while simultaneously meeting the building's heating or cooling demand.

The problem is not simply the size of the tank, but the mismatch between heat pump capacity, building load, storage capacity and charging time.

The objective of water tank sizing is not to maximize water volume, but to achieve the correct balance between system stability, energy demand and economic performance.

2. Understanding the Basic Thermal Energy Storage Formula

Before selecting a thermal storage tank, engineers and installers should understand the relationship between water volume, temperature difference and stored thermal energy.

The amount of thermal energy stored in water can be calculated using:

Q = m × Cp × ΔT

Where:

  • Q = Thermal energy

  • m = Mass of water (kg)

  • Cp = Specific heat capacity of water, approximately 4.186 kJ/(kg·K)

  • ΔT = Usable water temperature difference (°C or K)

For practical HVAC engineering calculations, this formula can be simplified to:

Q = 0.001163 × V × ΔT

Where:

  • Q = Stored thermal energy (kWh)

  • V = Water volume (litres)

  • ΔT = Usable temperature difference (°C)

This means that approximately 1,000 litres of water can store 1.163 kWh of thermal energy for every 1°C change in temperature.

Thermal energy storage capacity reference table

Water Tank Volume ΔT = 5°C ΔT = 10°C ΔT = 20°C
100 L 0.58 kWh 1.16 kWh 2.33 kWh
200 L 1.16 kWh 2.33 kWh 4.65 kWh
500 L 2.91 kWh 5.82 kWh 11.63 kWh
1,000 L 5.82 kWh 11.63 kWh 23.26 kWh
2,000 L 11.63 kWh 23.26 kWh 46.52 kWh
5,000 L 29.08 kWh 58.15 kWh 116.30 kWh
10,000 L 58.15 kWh 116.30 kWh 232.60 kWh

These values represent theoretical thermal storage capacity before accounting for tank heat losses, mixing and other system limitations.

Thermal energy is not the same as electrical energy

A common misunderstanding is that storing 1.163 kWh of thermal energy requires exactly 1.163 kWh of electricity.

This may be approximately true for direct electric resistance heating, but it is not true for a heat pump.

The electrical energy required by a heat pump depends on its coefficient of performance (COP).

Electrical Energy Consumption = Thermal Energy ÷ COP

For example, heating 1,000 litres of water from 30°C to 40°C requires approximately 11.63 kWh of thermal energy.

If the heat pump operates at an average COP of 4.0 during the charging process:

Electrical energy consumption = 11.63 ÷ 4.0 = 2.91 kWh

This calculation excludes additional circulation pump consumption and thermal losses.

Understanding the difference between thermal energy and electrical energy is fundamental to designing an economical thermal storage system.

3. How to Calculate the Required Buffer Tank Volume

A buffer tank is primarily designed to increase the active water volume of a hydronic system, stabilize water temperature and reduce excessive compressor cycling.

It should not be sized solely according to the building's floor area.

Method 1: Preliminary estimation based on floor area

In some residential heating projects, installers use a simplified rule of approximately 1 litre of buffer tank volume per square metre of heated floor area.

For example:

Heated Floor Area Preliminary Buffer Tank Volume
100 m² 100 L
150 m² 150 L
200 m² 200 L
300 m² 300 L

However, this is only a preliminary empirical reference.

Two buildings with the same floor area may have completely different heat losses, heat pump capacities, terminal units and hydraulic configurations.

Therefore, this method should never replace an engineering calculation or the heat pump manufacturer's minimum water volume requirements.

Method 2: Calculation based on minimum compressor operating time

A more technically reliable approach is to calculate the active water volume required to absorb excess heat pump output during low-load operation.

The simplified formula is:

V = 14.33 × Pnet × t ÷ ΔT

Where:

  • V = Required active system water volume (L)

  • Pnet = Heat pump output minus the simultaneous building heating load (kW)

  • t = Desired minimum compressor operating time (minutes)

  • ΔT = Allowable water temperature variation (°C)

Practical example

Consider a 12 kW inverter air-to-water heat pump with the following operating conditions:

  • Minimum modulated heating capacity: 4 kW

  • Minimum building heating demand: 1.5 kW

  • Desired minimum operating time: 10 minutes

  • Allowable water temperature variation: 5°C

The excess heating capacity is:

Pnet = 4 − 1.5 = 2.5 kW

The required active water volume is:

V = 14.33 × 2.5 × 10 ÷ 5

V = approximately 72 litres

If the existing system provides 30 litres of effective circulating water volume under this operating condition, the additional buffer volume required is approximately:

72 − 30 = 42 litres

A commercially available 50-litre buffer tank could therefore be considered, provided it also satisfies the manufacturer's minimum water volume, flow rate and defrost requirements.

Important: Water contained in hydraulically isolated or closed heating circuits should not automatically be included in the available active water volume.

4. How to Calculate the Required Thermal Storage Tank Volume

Unlike a conventional buffer tank, a thermal storage tank is specifically designed to store useful heating or cooling energy for later use.

Its capacity depends primarily on:

  • Building heating or cooling demand.

  • Required energy storage duration.

  • Available charging time.

  • Usable water temperature difference.

  • Heat pump output under actual charging conditions.

  • Thermal storage efficiency.

The simplified calculation formula is:

V = 860 × Q ÷ ΔT

Where:

  • V = Required water storage volume (L)

  • Q = Required thermal energy storage capacity (kWh)

  • ΔT = Usable water temperature difference (°C)

Example 1: Thermal storage for winter heating

A building requires an average heating capacity of 10 kW for four hours.

Required thermal energy:

Q = 10 × 4 = 40 kWh

Assume the storage tank can operate between 45°C and 35°C.

Usable temperature difference:

ΔT = 10°C

Required storage volume:

V = 860 × 40 ÷ 10

V = 3,440 litres

The theoretical minimum storage capacity is approximately 3.44 m³.

If only 90% of the theoretical stored energy is effectively usable, the required capacity increases to approximately 3.82 m³.

A 4,000-litre thermal storage tank could be evaluated for this application.

Example 2: Chilled water storage for an office building

An office building requires 20 kW of cooling capacity for six hours during peak electricity tariff periods.

Required cooling energy:

Q = 20 × 6 = 120 kWh

Assume the chilled water storage system operates between 7°C and 12°C.

Usable temperature difference:

ΔT = 5°C

Required storage volume:

V = 860 × 120 ÷ 5

V = 20,640 litres

The theoretical storage volume is approximately 20.6 m³, before accounting for thermal losses, mixing and unusable storage capacity.

One important conclusion is that chilled water storage systems often require relatively large tanks because their usable water temperature difference is limited.

It is also necessary to verify whether the heat pump or chiller can recharge the tank within the available off-peak operating period.

5. Selecting the Right Water Tank Material

Water tanks used in heat pump systems are available in several materials.

The appropriate choice depends on operating pressure, water quality, temperature, corrosion resistance, installation environment and project budget.

Tank Material Main Advantages Limitations Typical Applications
SUS304 Stainless Steel Good corrosion resistance, durability and clean construction Sensitive to certain high-chloride environments Residential and commercial hydronic systems
SUS316L Stainless Steel Improved resistance to chloride-related corrosion compared with 304 Higher investment cost Projects with more demanding water quality
Enamel-Coated Steel Good corrosion protection when the coating is intact Coating integrity and anode maintenance may require attention Hot water storage and compatible buffer tanks
Carbon Steel Good mechanical strength and cost-effectiveness Requires appropriate water treatment and corrosion protection Large closed-loop HVAC systems
Fibreglass-Reinforced Plastic (FRP) Lightweight and corrosion-resistant Pressure and temperature limitations vary by design Large atmospheric storage systems
Polyethylene (PE) Lightweight, economical and resistant to many chemicals Temperature and pressure limitations Suitable low-temperature, non-pressurized applications

For many conventional heat pump projects, SUS304 stainless steel is a practical option when the water chemistry and operating conditions are compatible.

However, stainless steel alone does not guarantee excellent thermal insulation. Thermal performance depends mainly on the insulation material, thickness, continuity and structural design.

For pressurized closed-loop systems, the tank must be specifically designed and rated for the maximum operating pressure and temperature.

An atmospheric storage tank must never be used as a pressurized vessel unless it is explicitly designed and certified for that purpose.

6. Water Tank Insulation: An Often-Overlooked Factor

A thermal storage tank is only effective when it can retain the energy stored inside it.

Poor insulation can cause valuable heating or cooling energy to be lost before it is needed.

This is especially important in cold climates, outdoor installations and systems with long thermal storage periods.

Recommended preliminary insulation thickness

The following thickness ranges may be used as initial engineering references for suitable high-performance insulation materials.

Installation Environment Indicative Insulation Thickness
Mild climate or conditioned indoor plant room 40–50 mm
Unheated plant room or colder climate 60–80 mm
Cold climate or exposed outdoor installation 80–100 mm or more
Large thermal storage or extended storage duration Based on thermal loss calculation

These values are not universal design requirements. Actual insulation thickness should be calculated according to thermal conductivity, tank dimensions, ambient temperature, operating temperature and acceptable standby losses.

Why 360-degree insulation is essential

Some installations provide insulation around the sides of the tank but neglect the top, bottom, pipe connections and structural supports.

These areas can create thermal bridges and significantly increase heat losses.

A well-designed tank should include:

  • Continuous insulation around the cylindrical or rectangular tank body.

  • Insulated top and bottom surfaces.

  • Insulated pipe connections and fittings.

  • Appropriate treatment of structural thermal bridges.

  • Weather-resistant external protection for outdoor installations.

  • A continuous vapour barrier for chilled water applications.

In cooling systems, vapour-tight insulation is especially important because condensation can damage insulation materials, promote corrosion and reduce long-term thermal performance.

A simple heat loss calculation

The steady-state thermal loss through an insulated tank can be estimated using:

P = U × A × ΔT

Where:

  • P = Thermal loss (W)

  • U = Overall heat transfer coefficient (W/m²·K)

  • A = External heat transfer surface area (m²)

  • ΔT = Temperature difference between stored water and surrounding air (K)

Assume a thermal storage tank has:

  • Surface area: 10 m²

  • Overall heat transfer coefficient: 0.4 W/m²·K

  • Water temperature: 45°C

  • Ambient temperature: 5°C

Estimated heat loss:

P = 0.4 × 10 × 40 = 160 W

Over 24 hours, the estimated thermal energy loss is:

0.16 × 24 = 3.84 kWh

Actual losses may be higher when pipe connections, structural supports and other thermal bridges are included.

This example demonstrates why insulation quality is as important as storage capacity.

7. Correct Design of Water Tank Inlet and Outlet Connections

The location of water inlet and outlet connections affects hydraulic performance, temperature stratification, usable storage capacity and maintenance.

Incorrect connection positions may cause excessive internal mixing, reduce the amount of usable stored energy or allow sediment to enter the circulating water system.

Heating water storage systems

Hot water is less dense than colder water and naturally tends to rise.

For a stratified heating storage tank:

  • Hot charging water should generally enter near the upper section.

  • Hot water supplied to the heating terminals should generally be drawn from the upper section.

  • Cooler return water should generally enter near the lower section.

  • Water returning to the heat pump is typically drawn from the lower section.

This arrangement helps maintain thermal stratification.

Chilled water storage systems

At conventional HVAC chilled water temperatures above approximately 4°C, colder water is denser than warmer water.

For a stratified chilled water storage tank:

  • Chilled water should generally enter near the lower section.

  • Chilled water supplied to the cooling terminals should generally be drawn from the lower section.

  • Warmer return water should generally enter near the upper section.

Low-velocity inlet diffusers may be required to reduce turbulence and preserve stratification.

Should pipe connections be positioned 200 mm from the tank top and bottom?

In some conventional water tank designs, engineers locate connections approximately 200 mm below the tank top and 200 mm above the tank bottom.

This can provide space for air collection, sediment accumulation and internal connection arrangements.

However, this distance is not a universal standard.

The correct nozzle elevation depends on:

  • Tank height and diameter.

  • Effective operating water volume.

  • Internal flow velocity.

  • Tank configuration and hydraulic function.

  • Temperature stratification requirements.

  • Sediment collection and maintenance provisions.

For atmospheric tanks, the upper connection must also be coordinated with the normal operating water level, freeboard and overflow arrangement.

For pressurized tanks, nozzle design must comply with the vessel's structural and pressure requirements.

8. Correct Installation of the Temperature Sensor

Temperature sensor positioning is critical to heat pump control logic.

If the sensor is installed in the wrong position, the controller may receive a temperature reading that does not accurately represent the available thermal energy.

This can lead to:

  • Premature compressor shutdown.

  • Unnecessary compressor operation.

  • Insufficient heating or cooling capacity.

  • Incorrect charging and discharging control.

  • Excessive temperature fluctuations.

In some conventional buffer tank applications, a sensor positioned approximately two-thirds of the tank height from the bottom may provide a useful upper-middle temperature measurement.

However, the optimal sensor position depends on its control function.

Sensor Position Typical Function
Upper section Monitor available hot water in heating storage systems
Middle section Monitor intermediate tank temperature
Lower section Monitor return water conditions or available chilled water
Multiple elevations Evaluate thermal stratification and charging status

For large thermal energy storage tanks, using multiple temperature sensors is generally preferable to relying on a single measurement point.

Sensors should preferably be installed in suitable immersion pockets or thermowells, with good thermal contact and appropriate insulation.

9. Tank Bottom Structure and Load-Bearing Design

The bottom structure of a water tank is frequently overlooked during installation.

Water is heavy. One cubic metre of water weighs approximately one metric tonne.

Water Tank Capacity Approximate Water Weight
500 L 500 kg
1,000 L 1,000 kg
2,000 L 2,000 kg
5,000 L 5,000 kg
10,000 L 10,000 kg
20,000 L 20,000 kg

These figures exclude the weight of the tank, insulation, support structure and accessories.

When a tank is filled with water, its bottom insulation and supporting structure may be subjected to significant compressive loads.

If the bottom structure is improperly designed, several problems may occur:

  • Insulation compression and deformation.

  • Reduced thermal resistance.

  • Structural settlement.

  • Tank bottom distortion.

  • Increased thermal losses through the supporting structure.

  • Mechanical stress on connected pipework.

A properly designed installation should include a structurally adequate foundation, suitable load distribution and insulation materials with sufficient long-term compressive strength.

When steel reinforcement or support structures are used, thermal bridging must also be considered.

The support structure must safely transfer the load without compromising the insulation system.

For large commercial tanks, rooftop installations and elevated plant rooms, structural verification by a qualified engineer is essential.

10. Choosing the Correct Hydraulic Configuration

Different water tank configurations serve different system requirements.

Two-pipe buffer tank

A two-pipe tank installed in series is commonly used to increase the active system water volume.

Its main advantages include:

  • Relatively simple hydraulic design.

  • Increased thermal inertia.

  • Limited additional equipment requirements.

  • Reduced short cycling when correctly sized.

However, a series buffer tank does not automatically provide hydraulic separation between the heat pump and distribution circuits.

Four-pipe buffer tank

A four-pipe buffer tank can provide hydraulic separation between the primary heat pump circuit and secondary distribution circuits.

This configuration

biểu ngữ
Thông tin chi tiết
Nhà > Tin tức >

Tin tức công ty về-Expansion Tank vs. Buffer Tank vs. Thermal Storage Tank – Part 4: Tank Selection, Sizing, Design and Installation in Heat Pump Systems

Expansion Tank vs. Buffer Tank vs. Thermal Storage Tank – Part 4: Tank Selection, Sizing, Design and Installation in Heat Pump Systems

2026-11-18

Expansion Tank vs. Buffer Tank vs. Thermal Storage Tank – Part 4: Tank Selection, Sizing, Design and Installation in Heat Pump Systems

Introduction

In an air-to-water heat pump system, selecting a high-efficiency heat pump is only the first step toward achieving reliable performance, indoor comfort and low operating costs.

The design of the water system is equally important, particularly the selection, sizing and installation of buffer tanks and thermal energy storage tanks.

An undersized water tank may result in frequent compressor cycling, insufficient thermal storage and unstable water temperatures. An oversized tank, however, may increase initial investment, standby heat losses and system response time.

Furthermore, inappropriate material selection, insufficient insulation, incorrect pipe connection positions and poor structural design can significantly affect overall system performance.

In the previous three articles of this technical series, we discussed:

  • Part 1: Expansion Tanks – Pressure Control and System Protection

  • Part 2: Buffer Tanks – Hydraulic Stability and Compressor Protection

  • Part 3: Thermal Storage Tanks – Energy Storage and Operating Cost Optimization

In this fourth article, we will explain how to correctly select, size, design and install water tanks for air-source heat pump heating and cooling systems.

1. Why Is Correct Water Tank Sizing Important?

One of the most frequently asked questions in the HVAC industry is:

How large should a buffer tank or thermal storage tank be for a heat pump system?

There is no universal answer because different applications have different hydraulic and thermal requirements.

If the water tank is too small

An undersized tank may cause:

  • Frequent compressor start-stop cycles, also known as short cycling.

  • Rapid fluctuations in supply and return water temperatures.

  • Insufficient thermal energy available during defrosting.

  • Reduced system stability under partial-load conditions.

  • Insufficient thermal storage capacity.

  • Increased mechanical stress on system components.

If the water tank is too large

An oversized tank may result in:

  • Higher equipment and installation costs.

  • Longer initial heating or cooling times.

  • Increased standby thermal losses.

  • Greater installation space requirements.

  • Additional structural loading.

  • Difficulty completing thermal charging within the available operating period.

For example, if an office building uses a large thermal storage tank with an undersized heat pump, the heat pump may not have sufficient capacity to charge the tank while simultaneously meeting the building's heating or cooling demand.

The problem is not simply the size of the tank, but the mismatch between heat pump capacity, building load, storage capacity and charging time.

The objective of water tank sizing is not to maximize water volume, but to achieve the correct balance between system stability, energy demand and economic performance.

2. Understanding the Basic Thermal Energy Storage Formula

Before selecting a thermal storage tank, engineers and installers should understand the relationship between water volume, temperature difference and stored thermal energy.

The amount of thermal energy stored in water can be calculated using:

Q = m × Cp × ΔT

Where:

  • Q = Thermal energy

  • m = Mass of water (kg)

  • Cp = Specific heat capacity of water, approximately 4.186 kJ/(kg·K)

  • ΔT = Usable water temperature difference (°C or K)

For practical HVAC engineering calculations, this formula can be simplified to:

Q = 0.001163 × V × ΔT

Where:

  • Q = Stored thermal energy (kWh)

  • V = Water volume (litres)

  • ΔT = Usable temperature difference (°C)

This means that approximately 1,000 litres of water can store 1.163 kWh of thermal energy for every 1°C change in temperature.

Thermal energy storage capacity reference table

Water Tank Volume ΔT = 5°C ΔT = 10°C ΔT = 20°C
100 L 0.58 kWh 1.16 kWh 2.33 kWh
200 L 1.16 kWh 2.33 kWh 4.65 kWh
500 L 2.91 kWh 5.82 kWh 11.63 kWh
1,000 L 5.82 kWh 11.63 kWh 23.26 kWh
2,000 L 11.63 kWh 23.26 kWh 46.52 kWh
5,000 L 29.08 kWh 58.15 kWh 116.30 kWh
10,000 L 58.15 kWh 116.30 kWh 232.60 kWh

These values represent theoretical thermal storage capacity before accounting for tank heat losses, mixing and other system limitations.

Thermal energy is not the same as electrical energy

A common misunderstanding is that storing 1.163 kWh of thermal energy requires exactly 1.163 kWh of electricity.

This may be approximately true for direct electric resistance heating, but it is not true for a heat pump.

The electrical energy required by a heat pump depends on its coefficient of performance (COP).

Electrical Energy Consumption = Thermal Energy ÷ COP

For example, heating 1,000 litres of water from 30°C to 40°C requires approximately 11.63 kWh of thermal energy.

If the heat pump operates at an average COP of 4.0 during the charging process:

Electrical energy consumption = 11.63 ÷ 4.0 = 2.91 kWh

This calculation excludes additional circulation pump consumption and thermal losses.

Understanding the difference between thermal energy and electrical energy is fundamental to designing an economical thermal storage system.

3. How to Calculate the Required Buffer Tank Volume

A buffer tank is primarily designed to increase the active water volume of a hydronic system, stabilize water temperature and reduce excessive compressor cycling.

It should not be sized solely according to the building's floor area.

Method 1: Preliminary estimation based on floor area

In some residential heating projects, installers use a simplified rule of approximately 1 litre of buffer tank volume per square metre of heated floor area.

For example:

Heated Floor Area Preliminary Buffer Tank Volume
100 m² 100 L
150 m² 150 L
200 m² 200 L
300 m² 300 L

However, this is only a preliminary empirical reference.

Two buildings with the same floor area may have completely different heat losses, heat pump capacities, terminal units and hydraulic configurations.

Therefore, this method should never replace an engineering calculation or the heat pump manufacturer's minimum water volume requirements.

Method 2: Calculation based on minimum compressor operating time

A more technically reliable approach is to calculate the active water volume required to absorb excess heat pump output during low-load operation.

The simplified formula is:

V = 14.33 × Pnet × t ÷ ΔT

Where:

  • V = Required active system water volume (L)

  • Pnet = Heat pump output minus the simultaneous building heating load (kW)

  • t = Desired minimum compressor operating time (minutes)

  • ΔT = Allowable water temperature variation (°C)

Practical example

Consider a 12 kW inverter air-to-water heat pump with the following operating conditions:

  • Minimum modulated heating capacity: 4 kW

  • Minimum building heating demand: 1.5 kW

  • Desired minimum operating time: 10 minutes

  • Allowable water temperature variation: 5°C

The excess heating capacity is:

Pnet = 4 − 1.5 = 2.5 kW

The required active water volume is:

V = 14.33 × 2.5 × 10 ÷ 5

V = approximately 72 litres

If the existing system provides 30 litres of effective circulating water volume under this operating condition, the additional buffer volume required is approximately:

72 − 30 = 42 litres

A commercially available 50-litre buffer tank could therefore be considered, provided it also satisfies the manufacturer's minimum water volume, flow rate and defrost requirements.

Important: Water contained in hydraulically isolated or closed heating circuits should not automatically be included in the available active water volume.

4. How to Calculate the Required Thermal Storage Tank Volume

Unlike a conventional buffer tank, a thermal storage tank is specifically designed to store useful heating or cooling energy for later use.

Its capacity depends primarily on:

  • Building heating or cooling demand.

  • Required energy storage duration.

  • Available charging time.

  • Usable water temperature difference.

  • Heat pump output under actual charging conditions.

  • Thermal storage efficiency.

The simplified calculation formula is:

V = 860 × Q ÷ ΔT

Where:

  • V = Required water storage volume (L)

  • Q = Required thermal energy storage capacity (kWh)

  • ΔT = Usable water temperature difference (°C)

Example 1: Thermal storage for winter heating

A building requires an average heating capacity of 10 kW for four hours.

Required thermal energy:

Q = 10 × 4 = 40 kWh

Assume the storage tank can operate between 45°C and 35°C.

Usable temperature difference:

ΔT = 10°C

Required storage volume:

V = 860 × 40 ÷ 10

V = 3,440 litres

The theoretical minimum storage capacity is approximately 3.44 m³.

If only 90% of the theoretical stored energy is effectively usable, the required capacity increases to approximately 3.82 m³.

A 4,000-litre thermal storage tank could be evaluated for this application.

Example 2: Chilled water storage for an office building

An office building requires 20 kW of cooling capacity for six hours during peak electricity tariff periods.

Required cooling energy:

Q = 20 × 6 = 120 kWh

Assume the chilled water storage system operates between 7°C and 12°C.

Usable temperature difference:

ΔT = 5°C

Required storage volume:

V = 860 × 120 ÷ 5

V = 20,640 litres

The theoretical storage volume is approximately 20.6 m³, before accounting for thermal losses, mixing and unusable storage capacity.

One important conclusion is that chilled water storage systems often require relatively large tanks because their usable water temperature difference is limited.

It is also necessary to verify whether the heat pump or chiller can recharge the tank within the available off-peak operating period.

5. Selecting the Right Water Tank Material

Water tanks used in heat pump systems are available in several materials.

The appropriate choice depends on operating pressure, water quality, temperature, corrosion resistance, installation environment and project budget.

Tank Material Main Advantages Limitations Typical Applications
SUS304 Stainless Steel Good corrosion resistance, durability and clean construction Sensitive to certain high-chloride environments Residential and commercial hydronic systems
SUS316L Stainless Steel Improved resistance to chloride-related corrosion compared with 304 Higher investment cost Projects with more demanding water quality
Enamel-Coated Steel Good corrosion protection when the coating is intact Coating integrity and anode maintenance may require attention Hot water storage and compatible buffer tanks
Carbon Steel Good mechanical strength and cost-effectiveness Requires appropriate water treatment and corrosion protection Large closed-loop HVAC systems
Fibreglass-Reinforced Plastic (FRP) Lightweight and corrosion-resistant Pressure and temperature limitations vary by design Large atmospheric storage systems
Polyethylene (PE) Lightweight, economical and resistant to many chemicals Temperature and pressure limitations Suitable low-temperature, non-pressurized applications

For many conventional heat pump projects, SUS304 stainless steel is a practical option when the water chemistry and operating conditions are compatible.

However, stainless steel alone does not guarantee excellent thermal insulation. Thermal performance depends mainly on the insulation material, thickness, continuity and structural design.

For pressurized closed-loop systems, the tank must be specifically designed and rated for the maximum operating pressure and temperature.

An atmospheric storage tank must never be used as a pressurized vessel unless it is explicitly designed and certified for that purpose.

6. Water Tank Insulation: An Often-Overlooked Factor

A thermal storage tank is only effective when it can retain the energy stored inside it.

Poor insulation can cause valuable heating or cooling energy to be lost before it is needed.

This is especially important in cold climates, outdoor installations and systems with long thermal storage periods.

Recommended preliminary insulation thickness

The following thickness ranges may be used as initial engineering references for suitable high-performance insulation materials.

Installation Environment Indicative Insulation Thickness
Mild climate or conditioned indoor plant room 40–50 mm
Unheated plant room or colder climate 60–80 mm
Cold climate or exposed outdoor installation 80–100 mm or more
Large thermal storage or extended storage duration Based on thermal loss calculation

These values are not universal design requirements. Actual insulation thickness should be calculated according to thermal conductivity, tank dimensions, ambient temperature, operating temperature and acceptable standby losses.

Why 360-degree insulation is essential

Some installations provide insulation around the sides of the tank but neglect the top, bottom, pipe connections and structural supports.

These areas can create thermal bridges and significantly increase heat losses.

A well-designed tank should include:

  • Continuous insulation around the cylindrical or rectangular tank body.

  • Insulated top and bottom surfaces.

  • Insulated pipe connections and fittings.

  • Appropriate treatment of structural thermal bridges.

  • Weather-resistant external protection for outdoor installations.

  • A continuous vapour barrier for chilled water applications.

In cooling systems, vapour-tight insulation is especially important because condensation can damage insulation materials, promote corrosion and reduce long-term thermal performance.

A simple heat loss calculation

The steady-state thermal loss through an insulated tank can be estimated using:

P = U × A × ΔT

Where:

  • P = Thermal loss (W)

  • U = Overall heat transfer coefficient (W/m²·K)

  • A = External heat transfer surface area (m²)

  • ΔT = Temperature difference between stored water and surrounding air (K)

Assume a thermal storage tank has:

  • Surface area: 10 m²

  • Overall heat transfer coefficient: 0.4 W/m²·K

  • Water temperature: 45°C

  • Ambient temperature: 5°C

Estimated heat loss:

P = 0.4 × 10 × 40 = 160 W

Over 24 hours, the estimated thermal energy loss is:

0.16 × 24 = 3.84 kWh

Actual losses may be higher when pipe connections, structural supports and other thermal bridges are included.

This example demonstrates why insulation quality is as important as storage capacity.

7. Correct Design of Water Tank Inlet and Outlet Connections

The location of water inlet and outlet connections affects hydraulic performance, temperature stratification, usable storage capacity and maintenance.

Incorrect connection positions may cause excessive internal mixing, reduce the amount of usable stored energy or allow sediment to enter the circulating water system.

Heating water storage systems

Hot water is less dense than colder water and naturally tends to rise.

For a stratified heating storage tank:

  • Hot charging water should generally enter near the upper section.

  • Hot water supplied to the heating terminals should generally be drawn from the upper section.

  • Cooler return water should generally enter near the lower section.

  • Water returning to the heat pump is typically drawn from the lower section.

This arrangement helps maintain thermal stratification.

Chilled water storage systems

At conventional HVAC chilled water temperatures above approximately 4°C, colder water is denser than warmer water.

For a stratified chilled water storage tank:

  • Chilled water should generally enter near the lower section.

  • Chilled water supplied to the cooling terminals should generally be drawn from the lower section.

  • Warmer return water should generally enter near the upper section.

Low-velocity inlet diffusers may be required to reduce turbulence and preserve stratification.

Should pipe connections be positioned 200 mm from the tank top and bottom?

In some conventional water tank designs, engineers locate connections approximately 200 mm below the tank top and 200 mm above the tank bottom.

This can provide space for air collection, sediment accumulation and internal connection arrangements.

However, this distance is not a universal standard.

The correct nozzle elevation depends on:

  • Tank height and diameter.

  • Effective operating water volume.

  • Internal flow velocity.

  • Tank configuration and hydraulic function.

  • Temperature stratification requirements.

  • Sediment collection and maintenance provisions.

For atmospheric tanks, the upper connection must also be coordinated with the normal operating water level, freeboard and overflow arrangement.

For pressurized tanks, nozzle design must comply with the vessel's structural and pressure requirements.

8. Correct Installation of the Temperature Sensor

Temperature sensor positioning is critical to heat pump control logic.

If the sensor is installed in the wrong position, the controller may receive a temperature reading that does not accurately represent the available thermal energy.

This can lead to:

  • Premature compressor shutdown.

  • Unnecessary compressor operation.

  • Insufficient heating or cooling capacity.

  • Incorrect charging and discharging control.

  • Excessive temperature fluctuations.

In some conventional buffer tank applications, a sensor positioned approximately two-thirds of the tank height from the bottom may provide a useful upper-middle temperature measurement.

However, the optimal sensor position depends on its control function.

Sensor Position Typical Function
Upper section Monitor available hot water in heating storage systems
Middle section Monitor intermediate tank temperature
Lower section Monitor return water conditions or available chilled water
Multiple elevations Evaluate thermal stratification and charging status

For large thermal energy storage tanks, using multiple temperature sensors is generally preferable to relying on a single measurement point.

Sensors should preferably be installed in suitable immersion pockets or thermowells, with good thermal contact and appropriate insulation.

9. Tank Bottom Structure and Load-Bearing Design

The bottom structure of a water tank is frequently overlooked during installation.

Water is heavy. One cubic metre of water weighs approximately one metric tonne.

Water Tank Capacity Approximate Water Weight
500 L 500 kg
1,000 L 1,000 kg
2,000 L 2,000 kg
5,000 L 5,000 kg
10,000 L 10,000 kg
20,000 L 20,000 kg

These figures exclude the weight of the tank, insulation, support structure and accessories.

When a tank is filled with water, its bottom insulation and supporting structure may be subjected to significant compressive loads.

If the bottom structure is improperly designed, several problems may occur:

  • Insulation compression and deformation.

  • Reduced thermal resistance.

  • Structural settlement.

  • Tank bottom distortion.

  • Increased thermal losses through the supporting structure.

  • Mechanical stress on connected pipework.

A properly designed installation should include a structurally adequate foundation, suitable load distribution and insulation materials with sufficient long-term compressive strength.

When steel reinforcement or support structures are used, thermal bridging must also be considered.

The support structure must safely transfer the load without compromising the insulation system.

For large commercial tanks, rooftop installations and elevated plant rooms, structural verification by a qualified engineer is essential.

10. Choosing the Correct Hydraulic Configuration

Different water tank configurations serve different system requirements.

Two-pipe buffer tank

A two-pipe tank installed in series is commonly used to increase the active system water volume.

Its main advantages include:

  • Relatively simple hydraulic design.

  • Increased thermal inertia.

  • Limited additional equipment requirements.

  • Reduced short cycling when correctly sized.

However, a series buffer tank does not automatically provide hydraulic separation between the heat pump and distribution circuits.

Four-pipe buffer tank

A four-pipe buffer tank can provide hydraulic separation between the primary heat pump circuit and secondary distribution circuits.

This configuration